Differences
This shows you the differences between two versions of the page.
en:essais_des_sorties_relais [2016/01/27 09:33] |
en:essais_des_sorties_relais [2020/07/05 17:13] (current) |
||
---|---|---|---|
Line 1: | Line 1: | ||
+ | ==== Configuration of the Outputs of the control relays ==== | ||
+ | File ''/ | ||
+ | Edit the file with the command (Add this code at the end of the file just BEFORE "exit 0") | ||
+ | <code bash> | ||
+ | sudo nano / | ||
+ | </ | ||
+ | <code bash> | ||
+ | #RELAYS OUTPUTS | ||
+ | echo " | ||
+ | sleep 2 | ||
+ | echo out > / | ||
+ | echo " | ||
+ | sleep 2 | ||
+ | echo out > / | ||
+ | echo " | ||
+ | sleep 2 | ||
+ | echo out > / | ||
+ | echo " | ||
+ | sleep 2 | ||
+ | echo out > / | ||
+ | </ | ||
+ | |||
+ | ==== Tests of the Outputs of the control relays ==== | ||
+ | |||
+ | You can verify the correct functioning of the outputs of the relays with the following code | ||
+ | <code bash> | ||
+ | sudo nano test-relays.sh | ||
+ | </ | ||
+ | |||
+ | <code bash | test-relays.sh> | ||
+ | #!/bin/bash | ||
+ | # Sequence of testing the 4 relays | ||
+ | |||
+ | for i in `seq 20 23`; | ||
+ | do | ||
+ | echo 1 > / | ||
+ | sleep 1 | ||
+ | done | ||
+ | for i in `seq 20 23`; | ||
+ | do | ||
+ | echo 0 > / | ||
+ | sleep 1 | ||
+ | done | ||
+ | |||
+ | for i in `seq 20 23`; | ||
+ | do | ||
+ | echo 1 > / | ||
+ | done | ||
+ | sleep 1 | ||
+ | for i in `seq 20 23`; | ||
+ | do | ||
+ | echo 0 > / | ||
+ | done | ||
+ | |||
+ | |||
+ | </ | ||
+ | |||
+ | For running the code | ||
+ | <code bash> | ||
+ | sudo python test-relays.sh | ||
+ | </ | ||
+ | |||
+ | root@f5uii-serveur:/ | ||
+ | root@f5uii-serveur:/ | ||
+ | ==== Configuration of the Outputs of the control relays ==== | ||
+ | File ''/ | ||
+ | Edit the file with the command (Add this code at the end of the file just BEFORE "exit 0") | ||
+ | |||
+ | <code bash> | ||
+ | sudo nano / | ||
+ | </ | ||
+ | <code bash> | ||
+ | #RELAYS OUTPUTS | ||
+ | echo " | ||
+ | sleep 2 | ||
+ | echo out > / | ||
+ | echo " | ||
+ | sleep 2 | ||
+ | echo out > / | ||
+ | echo " | ||
+ | sleep 2 | ||
+ | echo out > / | ||
+ | echo " | ||
+ | sleep 2 | ||
+ | echo out > / | ||
+ | </ | ||
+ | |||
+ | ==== Tests of the Outputs of the control relays ==== | ||
+ | |||
+ | You can verify the correct functioning of the outputs of the relays with the following code | ||
+ | <code bash> | ||
+ | sudo nano test-relays.sh | ||
+ | </ | ||
+ | |||
+ | <code bash | test-relays.sh> | ||
+ | #!/bin/bash | ||
+ | # Sequence of testing the 4 relays | ||
+ | |||
+ | for i in `seq 20 23`; | ||
+ | do | ||
+ | echo 1 > / | ||
+ | sleep 1 | ||
+ | done | ||
+ | for i in `seq 20 23`; | ||
+ | do | ||
+ | echo 0 > / | ||
+ | sleep 1 | ||
+ | done | ||
+ | |||
+ | for i in `seq 20 23`; | ||
+ | do | ||
+ | echo 1 > / | ||
+ | done | ||
+ | sleep 1 | ||
+ | for i in `seq 20 23`; | ||
+ | do | ||
+ | echo 0 > / | ||
+ | done | ||
+ | |||
+ | |||
+ | </ | ||
+ | |||
+ | For running the code | ||
+ | <code bash> | ||
+ | sudo python test-relays.sh | ||
+ | </ | ||
+ | |||
+ | {{youtube> |