Differences
This shows you the differences between two versions of the page.
en:schema_version_1.0_prototype [2016/03/03 23:09] |
en:schema_version_1.0_prototype [2020/07/05 17:13] (current) |
||
---|---|---|---|
Line 1: | Line 1: | ||
+ | FIXME **Cette page n'est pas encore traduite entièrement. Merci de terminer la traduction**\\ // | ||
+ | ===== Carte électronique (version 1.0) ===== | ||
+ | |||
+ | The schematic of the board is available in PDF format. Prin in A3 for best resolution. | ||
+ | |||
+ | *{{: | ||
+ | {{: | ||
+ | |||
+ | {{: | ||
+ | |||
+ | {{: | ||
+ | |||
+ | {{: | ||
+ | ====Parts List catalog==== | ||
+ | |||
+ | | **Quantity** | **Component** | **Value** | | ||
+ | | 2 | C1,C3 | 220µF électrolytiques 16V | | ||
+ | | 1 | C2 | 100nF tantale | | ||
+ | | 8 | C4, | ||
+ | | 11 | C12, | ||
+ | | 1 | C17 | 1µF tantale | | ||
+ | | 2 | D1,D2 | 1N5820 | | ||
+ | | 2 | D3,D4 | LED rouge | | ||
+ | | 6 | D5, | ||
+ | | 2 | D7,D8 | 10BQ015 (CMS) ou 1N5819 | | ||
+ | | 4 | D9, | ||
+ | | 2 | IC1,IC8 | ULN2003 | | ||
+ | | 1 | IC2 | DS18B20 | | ||
+ | | 2 | IC3,IC6 | CNY74-4 | | ||
+ | | 1 | IC4 | MAX3232 | | ||
+ | | 1 | IC5 | MAX6369 | | ||
+ | | 1 | IC7 | MCP3204 | | ||
+ | | 1 | J1 | Connecteur 40 Raspberry Pi B+/2B | | ||
+ | | 4 | J4, | ||
+ | | 3 | J2,J6,J10 | RJ 12 : TX RPTER, RX RPTER, LINK | | ||
+ | | 1 | J16 | Connecteur-DC-2.1mm | | ||
+ | | 4 | K1,K2,K3,K4 | RT314A12 | | ||
+ | | 1 | L1 | 330 µH - 1 A | | ||
+ | | 12 | R1, | ||
+ | | 4 | R9, | ||
+ | | 4 | R33, | ||
+ | | 7 | R10, | ||
+ | | 2 | R14,R17 | 1K potentiomètre linéaire | | ||
+ | | 2 | R15,R18 | 10K potentiomètre linéaire | | ||
+ | | 3 | R19,R20,R21 | 4,7K 1/4W | | ||
+ | | 2 | R23,R24 | 10 1/4W | | ||
+ | | 8 | R25, | ||
+ | | 4 | Tr1, | ||
+ | | 1 | X1 | LM2575T-5 | | ||
+ | | 1 | X2 | KIM-055L | | ||
+ | | 4 | DIVERS | Entretoises 10mm M3 femelle/ | ||
+ | | 1 | DIVERS | Connecteurs SECABLE HE14 pas de 2,54mm droite 1x36 | | ||
+ | ==== Step by step Assembly description ==== | ||
+ | |||
+ | **1. The Power supply assy** | ||
+ | |||
+ | Power supply with module KIM-055L | ||
+ | |||
+ | {{: | ||
+ | |||
+ | The components list to be installed : | ||
+ | * Connector DC 2,1mm **J16** or **J17** Screw terminal. | ||
+ | * Diode **D1** 1N5820 **C1** and | ||
+ | * **C3** capacitor 220μF 16V | ||
+ | |||
+ | Test of the 5V output voltage | ||
+ | |||
+ | {{: | ||
+ | |||
+ | **2. PTT / SQUELCH assy** | ||
+ | |||
+ | PTT/SQUELCH assemby section | ||
+ | |||
+ | {{: | ||
+ | |||
+ | The components list to be installed: | ||
+ | * **IC8** ULN2003 | ||
+ | * **IC3** CNY74-4 | ||
+ | * **R1 à R8** 470 Ω | ||
+ | * **R9, R11** 1 kΩ | ||
+ | * **R10, R12** 10 kΩ | ||
+ | * **D3, D4** Led red 3mm (with + on resistor side, the longer leg) | ||
+ | * **D5, D6** Led green 3mm (with + on resistor side, the longer leg) | ||
+ | * **D7, D8** Diodes 10BQ015 | ||
+ | |||
+ | **3. AUDIO IN/OUT assy** | ||
+ | |||
+ | {{: | ||
+ | |||
+ | The components list to be installed: | ||
+ | |||
+ | * **C4 à C11** Capacitor 10μF | ||
+ | * **R13 et R16** 1 kΩ | ||
+ | * **R14 et R17** Potentiometer 1 kΩ | ||
+ | * **R15 et R18** Potentiometer 10 kΩ | ||
+ | * **J4, | ||
+ | * **TR1 à TR4** Isolation Transformer ETAL P1200 (There is a possible alternative see above picture). | ||
+ | * **J2, | ||
+ | <note warning> | ||
+ | Mistake in pin description on Board | ||
+ | {{ : | ||
+ | </ | ||
+ | |||
+ | |||
+ | ** THE ASSEMBLY IS TERMINATED FOR THE MINIMUM VERSION OF THE CARD. NOW WE ARE GOING TO START THE OPTIONAL PARTS. | ||
+ | |||
+ | |||
+ | **4. OPTO INPUTS assy** | ||
+ | |||
+ | {{: | ||
+ | |||
+ | {{: | ||
+ | |||
+ | The components list to be installed: | ||
+ | * **R33 à R36** 220 Ω (This value can be changed according to the input voltage. Here it's for 5V) | ||
+ | * **J26** connector 2x5 pins | ||
+ | * **IC6** CNY74-4 | ||
+ | * **R37 to R40** 10 kΩ | ||
+ | |||
+ | **5. WATCHDOG assy** | ||
+ | |||
+ | {{: | ||
+ | |||
+ | The components list to be installed: | ||
+ | * **IC5** MAX6369 | ||
+ | * **C14** Capacitor 0,1μF | ||
+ | * **PIN 2x1** Weld the 2 connectors. One is useful to activate the Watchdog and the other (RUN) to connect the RUN or P6 connector of release (Reset) of the Raspberry Pi. SET0 SET1 SET2 are jumpers (solder) to determine the time before reset if it does not send a signal. | ||
+ | |||
+ | A Watchdog " | ||
+ | |||
+ | {{: | ||
+ | |||
+ | {{: | ||
+ | |||
+ | As boot starting time exceeds 10 seconds, it is recommended to set the detection time (timeout) at maximum. As indicated in the above table, the 3 jumpers SET0, SET1 and SET2 needs to be closed (Weld the three pairs of squares). | ||
+ | |||
+ | {{: | ||
+ | |||
+ | **6. Connector I2C assy** | ||
+ | |||
+ | {{: | ||
+ | |||
+ | The installation is just prolonging the I2C connections that are on the Raspberry Pi. | ||
+ | |||
+ | **7. The 1 WIRE assy** | ||
+ | |||
+ | {{: | ||
+ | |||
+ | The components list to be installed: | ||
+ | * J20 and J21 Installation 2 connectors pin 3x1, for 1WIRE externals sensors. | ||
+ | * IC2 DS18B20 temperature sensor | ||
+ | * R21 4,7 kΩ resistor | ||
+ | {{: | ||
+ | |||
+ | Here an overall picture at this level of assembly. | ||
+ | |||
+ | **8. Output on Relay assy** | ||
+ | |||
+ | {{: | ||
+ | |||
+ | The components list to be installed: | ||
+ | * **IC1** ULN2003 | ||
+ | * **D13 à D16** green diode 3mm, (with + on resistor opposite side, the longer leg) | ||
+ | * **R41 à R44** 470 Ω resistors | ||
+ | * **D9 à D12** diodes 1N4148 | ||
+ | * **K1 à K4** relay 12V/ | ||
+ | * **J28 à J31** Terminal with 3 blocks Screw | ||
+ | |||
+ | **9. Analogic/ | ||
+ | |||
+ | {{: | ||
+ | |||
+ | The components list to be installed: | ||
+ | * IC7 MCP3204 R23 to R24 10 Ω resistors | ||
+ | * C15 to C18 0,1 µF | ||
+ | * the resistors R25 to R32 (bridge voltage divider), will be determined depending on the voltage to be measured. | ||
+ | * It remains the connector Pin **J25** 5x1 and the connector Pin 2x1 for the jumper **JP13** used to connect the grounds Card/ | ||
+ | |||
+ | |||
+ | **10. RS232 Port assy** | ||
+ | |||
+ | {{: | ||
+ | |||
+ | The components list to be installed: | ||
+ | * **IC4** MAX3232 | ||
+ | * **C19 à C23** capacitor 0,1µF | ||
+ | * Connector PIN 3x1 will be used to connect RXD,TXD,GNG on a DB9 connector for example. | ||
+ | |||
+ | |||
+ | **11. Connector Raspberry Pi assy** | ||
+ | |||
+ | {{: | ||
+ | |||
+ | {{: | ||
+ | |||
+ | The components list to be installed: | ||
+ | * Connector 40 pins female | ||
+ | |||
+ | The Raspberry Pi is fixed on the card with 4 spacers 10mm and 8 screws M3, this is a temporary assembly because you'll have to add spacers to secure definitively the card in a box. | ||
+ | |||
+ | **12. Final result of assy** | ||
+ | |||
+ | {{: | ||
+ | |||
+ | {{: | ||
+ | |||
+ | **13. GPIO used on the Raspberry Pi** | ||
+ | |||
+ | {{: | ||
+ | |||
+ | {{: |